日本不卡二区,夜夜高潮夜夜爽高清完整版1,丁香成人免费视频,欧美日本高清

當前位置:首頁-新聞資訊

怎么減少鋁單板不必要的浪費呢?

來源:http://m.igugo.cn/ 發布時間:2023-08-17

鋁單板它在我們生活中的使用是很廣泛的,但是對于鋁單板還有很多行外的人不是很了解,鋁單板它進行加工的時候會經常出現浪費的現象,難免會出現浪費的情況,下面就向大家介紹下:
Aluminum veneers are widely used in our daily lives, but there are still many laypeople who are not very familiar with them. When processing aluminum veneers, there is often waste, which is inevitable. Below is an introduction to everyone:
1.揉捏調直環節
1. Kneading and straightening process
調直這個環節,比較簡略讓型材產生曲折,操作員必定要注意調直所用的力度,假定力度過大就,或許型材就簡略產生變形、收口、桔皮等現象,而力氣過小就會產生型材調不直,構成型材曲折。
Straightening is a relatively simple process that can cause twists and turns in the profile. The operator must pay attention to the force used for straightening. Assuming that the force is too large, the profile may experience deformation, closing, orange peel, and other phenomena. However, if the force is too small, the profile may not be straightened, resulting in twists and turns in the profile.
2.揉捏裝框
2. Kneading and framing
鋁板生產廠家
這個環節也是非常重要的,鋸?fù)甓ǔ唛L度后,一般鋁單板就要進行裝框了,這時應該要注意了:這料是大料仍是小料,是帶管料仍是平面模拉出來的料。
This link is also very important. After sawing the fixed length, the aluminum veneer usually needs to be framed. At this time, it should be noted that this material is large or small, whether it is a tube material or a flat die drawn material.
一般來說,大料和帶管的料抬兩頭裝框不簡略構成曲折,但小料和平面模拉出來的料,抬兩頭就很簡略構成曲折,這時就應該從兩頭向中心挨近進行抬料裝框。但有的型材即便這樣還不可,這時咱們就需要把這類料放在已時效的型材上再抬到框里。
Generally speaking, lifting the two ends of large materials and materials with pipes to frame is not a simple form of twists and turns, but lifting the two ends of small materials and materials pulled out of the flat mold is a simple form of twists and turns. At this point, the material should be lifted and framed from both ends closer to the center. But even if this is not possible for some profiles, we need to place these materials on the aged profiles and then lift them into the frame.
3.表面處理上架
3. Surface treatment on shelf
坯料經時效,硬度已達標,型材不會那么容易變彎曲,但是在上架時還是要注意,兩端抬料時,盡量避免上下大力波動,避免鋁單板出現彎曲的情況。
After aging, the hardness of the billet has reached the standard, and the profile is not prone to bending. However, it is still important to pay attention when placing it on the shelf. When lifting the material at both ends, try to avoid strong fluctuations in the upper and lower directions to avoid bending of the aluminum veneer.
本文由鋁板生產廠家發布,您是不是對這些內容有所了解了呢?更多的內容請點擊:http://m.igugo.cn我們會有更多精彩內容等你查看。
This article is published by the aluminum plate manufacturer. Have you gained some understanding of these contents? For more information, please click on: http://m.igugo.cn We will have more exciting content waiting for you to check out.
国产视频婷婷五月份| 周熟女乱子伦视频| 久久精品国产亚洲AV人妖| 91色婷婷91| WWW.夜啪啪。com| 在线国产日韩欧美精品三级| 综合色区网| 中女生被操视频| 日韩 欧美 91| 美日韩欧美精一二三区| 丁香成人一区二区| 国产主播av| 涩综合网址| 亚洲 天堂 欧美| 乱伦视频第一页| 国产av页| 久久亚洲熟女cc98cm成人视频| 蜜月视频毛片| 亚州国产精品一区二区| 欧美久久地址| 国产av亚洲av综合av| av小说在线免费观看| 小妹av一区二区三区| 久久久久久人要| 日本高潮不卡| 曰本不卡一区二区| AV美女AV在线| 又粗又猛久久人人爽视频| 日韩一区成人网| 美女AV影院美| 国产精品美女大鸡巴| 国产乱老熟视频乱老熟女51| 亚洲欧美人妻日韩| 成人 在线 亚洲| 欧美黄色片视频午夜福利| 亚洲伦理综合网| 日韩又粗又长又爽的视频| 欧美黄色片入口| 麻豆91精品秘 入口| 尤物在线入口一区| 亚洲 精在线|